Related topics

Does anyone know how to emulate modem response?
It may be a hardware PB or the following PB : May be Hyperterm do not send characters to the Cisco because of flow control hardware settings. Check the settings of hyperterm and set flow controle hard NONE. Hyperterminal is one of the WORST telnet/comm program I have EVER used in my ENTIRE life.

Sun 220R Monitorless problem
If I short out the TXD-RXD lines at the GPS end (with the GPS disconnected) and use Hyperterm, I can send from the keyboard out through the com port and back in to have it show on the screen. There is no problem with the port or the cable. (And yes, it's correct at the GPS end as well) and have you tried shorting

Help Disabling Call Waiting Please
Hyperterminal does not use the DUN connectoid, it uses the modem setup in the Control Panel. Set the modem properties for modem#2 in the Contol Panel | Modem | modem#2 Properties, then select modem#2 for use in the Hyperterminal session setup. -- --- I'm no expert, just trying to help --- ** Please remove "NOSPAM"

GPS320 apparent com port failure
Hyperterminal doesn't have a HOST mode, and we like to transfer files back and fourth between us. How do we do this?? I've been ALL OVER the help screens, it doesn't seem to be there.... Please give detailed instructions, I tend to be dense... Joe Joe, Type ATS0=1 to put HT in answer mode and you can transfer files

Win98 No modem release
COM comp unix solaris "Joe D." <newbie_from_new...@yahoo.com> writes: Oddly enough, I had a fellow go into the server room and pull the cable from the hyperterm, with no effect. I had read that doing so would crash the server? it didn't in my case....odd Apart from that "crash" is not the proper operative word,

Sun Enterprise 2 ; How to start the machine? ( no monitor ...
Jim Hargis jhar...@uswest.net microsoft public windowsce When looking around my Jornada 690 and Clio, I noticed that there was no Hyperterm equivalent in the communications folder. Where can I find one?? -- Jim Hargis j...@har-gis.com GIS Engineering.

Boca+windows95=No connect
Or Start | Run <type in> hypertrm.exe <enter> Follow this to get into Hyperterm http://support.microsoft.com/kb/q124890/ say anything to get to the term window type ATZ <enter> You might not see what your typing, but when you press enter you should get an OK. see if that works. Other AT commands you can use

"New" IIgs, but no system software
Make sure you set up Hyperterminal correctly because I think that's the problem you are having above. Here's a link to Hyperterminal setup procedures... http://808hi.com/56k/x2-hyperterm.htm Follow the directions closely. If you still get no response from the modem then you should consider the possibilities that

osp5000l parameters translation?
X4 - Report all call progress result codes and connection rate, ie, OK, CONNECT, RING, NO CARRIER, NO ANSWER, CONNECT XXXX, BUSY, NO DIALTONE and ERROR. X4 is the default. The manual doesn't list ! as one of the supported characters. OK, try using HyperTerm to send the command, if it returns ERROR then there's

free telnet programs
Running an Ultra 2 Enterprise with OBP 3.11 - No Sun monitor or keyboard - Using Windows Hyperterm through serial port to ttya. I have two systems. The other works just great, meaning no problems with Hyperterm or cable. The problem is trying to interact with the prom monitor. I can get the "ok" by entering CTL-BRK

Experience with Windows 95.
Even after looking at the PDF installation guide, which was NO HELP in this regard. The installation guide implies that it is keyed. Well, the cable is keyed, but the connector on the Modem Blaster card is not. After installing on Windows 2000, HyperTerm only recognizes the card less than half of the time.

Sparc IPX & IPC Help
I need the Linux equivalent of Windows' hyperterm connected to, say, COM1. That's all. No dialing, no modem, just a dumb terminal emulation. I don't care if it's a on a terminal or an X-Window program in Linux. I've written dumb terminals before and I suppose I could write one but I'd rather spend the time doing

Hyperterm
No I wasn't robbed, I knew its specs and it has been on the shelf for years ! Guess what .....its working now !! As a last resort I pulled the cable on my PC while it was booting (DON'T LAUGH !!!!!), rebooted the PC opened up hyperterminal and lo and behold "Huston we have lift off !! ", rebooting the PC didn't

linemakecall failure leads to tapisrv hang
Here is my hyperterm output for the download. The download is succseeful but no CE Target Control window appears and I get the "func 9" about every 5 secs. Thanks, Pat Microsoft Windows CE Ethernet Bootloader Common Library Version 1.1 Built Jan 2 2007 15:34:19 Microsoft Windows CE Ethernet Bootloader 3.5 for CE/PC

Help!! Modem 'No dialtone' problem
Pain in the A@# % %Still, no hyperterm. Still a long while later, I figured out that the %reliable Win95 wouldn't install hyperterm program because I already %had the hyperterm directory although it's empty. Again I felt very %proud for coming up with this correct reasoning. Not true 95 Will install over any

How to computer control a Sony SAT-B3? No daig port!!!!!
Dick Dievendorff die...@comcast.net elecraft-archive I had similar (lack of) luck with Hyperterm, TeraTerm, and TinyTerm on Windows Vista with a USB to Serial I already tried setting both terminals for 38400, 8 bits, no parity and 1 stop bit and the K3 is taling to MixW and Ham Radio Delux with these setting.

How do you install Hyperterm?
Hyperterm IS the best diagnostic. FInd the modem model and the AT commands to reset the modem. Then turn on the speaker (ATM1?) then enable the extended code for dial tone detection. Then do a dial of some sort (ATDT1). If you see "NO DIALTONE", I think the modem is fried! DP wrote: I have tried switching the phone

Hyperterm crashes when trying to use!
I posted this on win.98.comm.modem but got no answer. Any help here? I access a remote computer by using the Hyperterm program that came with my Windows 98 machine. It has worked in the past but recently I am able to log on, do what I want, but when it comes time to disconnect from the remote, I get the following

hyperterm in Linux?
If you are using hyperterm then you might not be able to generate a break. You also might have problems generating a break if you are using a USB to serial convertor. -- Live it up, rip it up, why so lazy? Give it out, dish it out, let's go crazy, yeah! -- Supertramp (The USENET Song)

Help! Apple IIc+ with no working diskettes
(3.51.4) Professional Reply-To: Bassford Liter <hypert...@bernama.com> X-Priority: 3 (Normal) Message-ID: <7260_________________5...@bernama.com> To: <x> Subject: repercussion Old johnny there waiting to see me, no end the second time, and began knotting them up in not seen you since x9o9, that time in ostend.